SSH is enabled and the default password for the 'pi' user has not been changed.
This is a security risk - please login as the 'pi' user and type 'passwd' to set a new password.

Done.
Done.
------------------------------
Model            : 7292
STA Type         : AP
Country          : EU
Security Mode    : OPEN
CAL. USE         : ON
AMPDU            : ON
Download FW      : uni_s1g.bin
TX Power         : 17
BSS MAX IDLE     : 180
------------------------------
NRC AP setting for HaLow...
[*] Set Max CPU Clock on RPi
1400000
1400000
1400000
1400000
Done
[0] Clear
hostapd: no process found
wireshark-gtk: no process found
rmmod: ERROR: Module nrc is not currently loaded
rm: cannot remove '/home/pi/nrc_pkg/script/conf/temp_self_config.conf': No such file or directory
[1] Copy
total 336
drwxr-xr-x 2 pi pi   4096 May 30 18:16 .
drwxr-xr-x 4 pi pi   4096 May 30 17:06 ..
-rwxr-xr-x 1 pi pi    362 May 25 18:40 copy
-rwxr-xr-x 1 pi pi    562 May 25 18:40 nrc7292_bd.dat
-rwxr-xr-x 1 pi pi 325628 May 25 18:40 nrc7292_cspi.bin
-rwxr-xr-x 1 root root 325628 May 25 18:40 /lib/firmware/uni_s1g.bin
====================================
 AP INTERFACE     : wlan0
 AP STATIC IP     : 192.168.200.1 
 NET MASK NUM     : 24 
====================================
Config for AP is done!
IP and DHCP config done
[2] Set Module Parameters
[3] Loading module
sudo modprobe nrc  hifspeed=20000000 spi_bus_num=0 spi_cs_num=0 spi_gpio_irq=5 spi_polling_interval=0 fw_name=uni_s1g.bin power_save=0 bss_max_idle=180 auto_ba=1 listen_interval=1000 credit_ac_be=40
[4] Set tx power
Tx power : 17			Calibration_use : ON
OK
Board Data use			 : off
OK
[5] Set guard interval
guard interval : long
OK
[6] Set cal_use
Calibration_use : on			Country	 : EU
OK
[*] Start DHCPCD and DNSMASQ
[*] Self configuration off
[6] Start hostapd on wlan0
[*] configure file copied from: /home/pi/nrc_pkg/script/conf/EU/ap_halow_open.conf
Configuration file: /home/pi/nrc_pkg/script/conf/temp_hostapd_config.conf
wlan0: interface state UNINITIALIZED->COUNTRY_UPDATE
Using interface wlan0 with hwaddr 00:c0:ca:ae:76:56 and ssid "halow_demo"
wlan0: interface state COUNTRY_UPDATE->ENABLED
wlan0: AP-ENABLED 
[7] Start NAT
[8] ifconfig
docker0: flags=4099<UP,BROADCAST,MULTICAST>  mtu 1500
        inet 172.17.0.1  netmask 255.255.0.0  broadcast 172.17.255.255
        ether 02:42:e4:6d:3c:eb  txqueuelen 0  (Ethernet)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

eth0: flags=4099<UP,BROADCAST,MULTICAST>  mtu 1500
        ether dc:a6:32:15:bf:05  txqueuelen 1000  (Ethernet)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 65536
        inet 127.0.0.1  netmask 255.0.0.0
        inet6 ::1  prefixlen 128  scopeid 0x10<host>
        loop  txqueuelen 1000  (Local Loopback)
        RX packets 190  bytes 14783 (14.4 KiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 190  bytes 14783 (14.4 KiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

wlan0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
        inet 192.168.200.1  netmask 255.255.255.0  broadcast 192.168.200.255
        inet6 fe80::97d8:64c:7f58:a78a  prefixlen 64  scopeid 0x20<link>
        ether 00:c0:ca:ae:76:56  txqueuelen 1000  (Ethernet)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 17  bytes 2238 (2.1 KiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

HaLow AP ready
--------------------------------------------------------------------
Done.
Press any key to continue...